Four Stroke Cycle Engine :-
A four-stroke cycle engine is an internal combustion engine that utilizes four distinct piston strokes (intake, compression, power, and exhaust) to complete one operating cycle. The piston make two complete passes in the cylinder to complete one operating cycle. An operating cycle requires two revolutions (720°) of the crankshaft. The four-stroke cycle engine is the most common type of small engine. A four-stroke cycle engine completes five Strokes in one operating cycle, including intake, compression, ignition, power, and exhaust Strokes.
The intake event is when the air-fuel mixture is introduced to fill the combustion chamber. The intake event occurs when the piston moves from TDC to BDC and the intake valve is open. The movement of the piston toward BDC creates a low pressure in the cylinder. Ambient atmospheric pressure forces the air-fuel mixture through the open intake valve into the cylinder to fill the low pressure area created by the piston movement.
The cylinder continues to fill slightly past BDC as the air-fuel mixture continues to flow by its own inertia while the piston begins to change direction. The intake valve remains open a few degrees of crankshaft rotation after BDC. Depending on engine design. The intake valve then closes and the air-fuel mixture is sealed inside the cylinder.
The compression stroke is when the trapped air-fuel mixture is compressed inside the cylinder. The combustion chamber is sealed to form the charge. The charge is the volume of compressed air-fuel mixture trapped inside the combustion chamber ready for ignition. Compressing the air-fuel mixture allows more energy to be released when the charge is ignited. Intake and exhaust valves must be closed to ensure that the cylinder is sealed to provide compression. Compression is the process of reducing or squeezing a charge from a large volume to a smaller volume in the combustion chamber. The flywheel helps to maintain the momentum necessary to compress the charge.
When the piston of an engine compresses the charge, an increase in compressive force supplied by work being done by the piston causes heat to be generated. The compression and heating of the air-fuel vapor in the charge results in an increase in charge temperature and an increase in fuel vaporization. The increase in charge temperature occurs uniformly throughout the combustion chamber to produce faster combustion (fuel oxidation) after ignition.
The increase in fuel vaporization occurs as small droplets of fuel become vaporized more completely from the heat generated. The increased droplet surface area exposed to the ignition flame allows more complete burning of the charge in the combustion chamber. Only gasoline vapor ignites. An increase in droplet surface area allows gasoline to release more vapor rather than remaining a liquid.
The more the charge vapor molecules are compressed, the more energy obtained from the combustion process. The energy needed to compress the charge is substantially less than the gain in force produced during the combustion process. For example, in a typical small engine, energy required to compress the charge is only one-fourth the amount of energy produced during combustion.
The compression ratio of an engine is a comparison of the volume of the combustion chamber with the piston at BDC to the volume of the combustion chamber with the piston at TDC. This area, combined with the design and style of combustion chamber, determines the compression ratio. Gasoline engines commonly have a compression ratio ranging from 6:1 - 10:1. The higher the compression ratio, the more fuel-efficient the engine.
A higher compression ratio normally provides a substantial gain in combustion pressure or force on the piston. However, higher compression ratios increase operator effort required to start the engine. Some small engines feature a system to relieve pressure during the compression stroke to reduce operator effort required when starting the engine.
The power stroke is an engine operation Stroke in which hot expanding gases force the piston head away from the cylinder head. Piston force and subsequent motion are transferred through the connecting rod to apply torque to the crankshaft.
The torque applied initiates crankshaft rotation. The amount of torque produced is determined by the pressure on the piston, the size of the piston, and the throw of the engine. During the power Stroke, both valves are closed.
The exhaust stroke occurs whenspent gases are expelled from the combustion chamber and released to the atmosphere. The exhaust stroke is the final stroke and occurs when the exhaust valve is open and the intake valve is closed. Piston movement evacuates exhaust gases to the atmosphere.
As the piston reaches BDC during the power stroke combustion is complete and the cylinder is filled with exhaust gases. The exhaust valve opens, and inertia of the flywheel and other moving parts push the piston back to TDC, forcing the exhaust gases out through the open exhaust valve. At the end of the exhaust stroke, the piston is at TDC and one operating cycle has been completed.